Metal buildings in Peyton, CO — coordinated by Amsteel Midwest with a Project Advisor serving the Pikes Peak region. Peyton is where the Black Forest pines give way to open ranch country — bigger parcels than Falcon, horses and hay ground, and homesteads strung along Highway 24 east of the Springs. We coordinate tubular steel, cold formed steel, and red iron buildings built for that ground.
Like the rest of unincorporated El Paso County, Peyton permits through the Pikes Peak Regional Building Department — and like the rest of the Palmer Divide, it carries real snow loads. Address-specific engineering isn’t a sales line out here; it’s the product.
Which Type of Metal Building Fits Your Peyton Project?
Tubular Steel — Our Most Popular System
Tubular steel is our highest-volume product and the system our Project Advisors know best. At 30’–40′ wide, a properly spec’d tubular building delivers an excellent result at a price point that works for the majority of our buyers, and it remains viable through 60′ wide for agricultural applications. Foam closures, rat guard trim, rake edges, and gutter packages can all be added for a clean finished appearance, with headered eave wall openings up to 20′ wide. Site-specific engineering runs approximately $2.00 per square foot when required.
Cold Formed Steel — Finished Buildings, Municipalities, and Barndominiums
Cold formed steel comes standard with foam closure systems, soffit options, upgraded trim packages, rat guard trim, rake edges, gutter packages, and standing seam roof options — properly sealed eaves from the start. It handles clear spans up to 60′ wide at approximately 15′ on center standard column spacing, and site-specific engineering runs approximately $0.75 per square foot — significantly less than tubular when engineering is required. In Colorado, where permits and engineered drawings are the norm nearly everywhere, that engineering cost difference makes cold formed the frequent total-cost winner for barndominiums, residential shells, finished workshops, and permitted projects.
Red Iron — 60’+ Spans, Large Door Openings, and Commercial Applications
Red iron pre-engineered structural steel is the standard for buildings 60′ wide and above and for commercial or industrial applications requiring door openings wider than 20′. At 25’–30′ on center standard frame spacing, red iron delivers wide open bay configurations for large equipment facilities, indoor riding arenas, commercial buildings, and agricultural structures.
Not sure which system fits your Peyton project? Read our complete comparison guide: Tubular Steel vs. Cold Formed Steel vs. Red Iron — or call us and we’ll work through it with you directly.
What Peyton Buyers Are Building
Peyton projects lean rural: horse barns, loafing sheds, hay and equipment storage, and shops on ten-to-eighty-acre parcels, plus garages and RV covers for the households. Under PPRBD engineering requirements, cold formed steel frequently wins for enclosed and finished buildings on total project cost, while tubular stays competitive on smaller certified structures and open-sided ag buildings where the county’s process allows. Indoor arenas and 60’+ clear spans go red iron.
Permitting in Peyton — What You Need to Know
Peyton is unincorporated El Paso County, so permits run through the Pikes Peak Regional Building Department, with engineered drawings required on most structures. Palmer Divide elevation means snow loads run above the Springs baseline. We run the ASCE 7 hazard tool against your specific Peyton address, prepare the PPRBD documentation, and confirm your parcel’s requirements before you finalize.
Amsteel Midwest runs the ASCE 7 hazard tool against your specific project address, provides all engineered drawings and documentation, and advises on your jurisdiction’s requirements before you finalize your design. Installation is coordinated through manufacturer install networks for tubular buildings and referred professional installers for cold formed and red iron projects.
Serving Peyton and Surrounding Communities
We serve Peyton and its neighbors, including Falcon, Calhan, Black Forest, Elbert, Ellicott, and the greater Pikes Peak region. See the full Metal Buildings Colorado Springs CO page or browse all our Colorado metal building locations.
Talk to a Project Advisor About Your Peyton Project
Whether you know exactly what you want or you’re just starting to think through your options, a conversation with one of our Project Advisors is the most efficient path to the right answer. We’ll ask about your site, your use case, your local requirements, and your budget — and give you a straight recommendation.
- Call us: 417-218-8348
- Email: sales@amsteelmidwest.com
- Submit a project inquiry here
- Design your building online
Frequently Asked Questions — Metal Buildings Peyton CO
What is the best type of metal building for Peyton?
For barns, shops, and garages under PPRBD requirements and Divide snow loads, cold formed steel is the frequent winner. Smaller certified buildings and qualifying open ag structures keep tubular in play, and indoor arenas or 60’+ spans are red iron work.
Do I need a permit for a metal building in Peyton?
Yes — Peyton is unincorporated El Paso County, and PPRBD requires permits with engineered drawings on most structures. One office covers the whole region, and we handle the documentation as part of the project.
What metal building sizes are most popular in Peyton?
Our most popular configurations are 30×40 and 30×50 for residential and small agricultural buyers, with larger agricultural and commercial operations frequently requesting 40×60 through 60×80. Browse our full inventory here.
Amsteel Midwest | 1014 E Broadway St, Bolivar, MO 65613 | 417-218-8348 | sales@amsteelmidwest.com
Metal Buildings in Colorado | Metal Buildings Colorado Springs CO | View Inventory | Contact Us