Metal buildings in Bennett, CO — coordinated by Amsteel Midwest with a Project Advisor serving the Denver metro. Bennett is the plains east of Denver holding their own — I-70 corridor acreage, working farm and ranch ground, and families who traded the metro for horizon. Buildings out here have jobs: equipment sheds, hay barns, shops, and garages. We coordinate all three systems that do the work — tubular, cold formed, and red iron.
Bennett straddles the Adams–Arapahoe county line, and both counties run building departments — so which side your parcel sits on, and whether you’re in town, sets the process. We confirm that for your specific address before anything gets quoted.
Which Type of Metal Building Fits Your Bennett Project?
Tubular Steel — Our Most Popular System
Tubular steel is our highest-volume product and the system our Project Advisors know best. At 30’–40′ wide, a properly spec’d tubular building delivers an excellent result at a price point that works for the majority of our buyers, and it remains viable through 60′ wide for agricultural applications. Foam closures, rat guard trim, rake edges, and gutter packages can all be added for a clean finished appearance, with headered eave wall openings up to 20′ wide. Site-specific engineering runs approximately $2.00 per square foot when required.
Cold Formed Steel — Finished Buildings, Municipalities, and Barndominiums
Cold formed steel comes standard with foam closure systems, soffit options, upgraded trim packages, rat guard trim, rake edges, gutter packages, and standing seam roof options — properly sealed eaves from the start. It handles clear spans up to 60′ wide at approximately 15′ on center standard column spacing, and site-specific engineering runs approximately $0.75 per square foot — significantly less than tubular when engineering is required. In Colorado, where permits and engineered drawings are the norm nearly everywhere, that engineering cost difference makes cold formed the frequent total-cost winner for barndominiums, residential shells, finished workshops, and permitted projects.
Red Iron — 60’+ Spans, Large Door Openings, and Commercial Applications
Red iron pre-engineered structural steel is the standard for buildings 60′ wide and above and for commercial or industrial applications requiring door openings wider than 20′. At 25’–30′ on center standard frame spacing, red iron delivers wide open bay configurations for large equipment facilities, indoor riding arenas, commercial buildings, and agricultural structures.
Not sure which system fits your Bennett project? Read our complete comparison guide: Tubular Steel vs. Cold Formed Steel vs. Red Iron — or call us and we’ll work through it with you directly.
What Bennett Buyers Are Building
Bennett projects are plains-practical: equipment and hay storage, shops for the operation, garages and RV covers for the households along the I-70 corridor. With engineered drawings the norm in both counties, cold formed steel’s engineering cost advantage makes it the frequent winner for finished shops and garages, while tubular stays competitive on smaller certified buildings. Large equipment barns at 60’+ clear spans go red iron.
Permitting in Bennett — What You Need to Know
Projects inside Bennett town limits permit through the Town of Bennett; unincorporated ground permits through Adams or Arapahoe County depending on which side of the line you sit — both run building departments with adopted codes. Expect permits and engineered drawings on most structures, with narrower agricultural processes than the southern plains. We run the ASCE 7 hazard tool against your specific Bennett address — plains wind is real out here — and confirm your county before you finalize.
Amsteel Midwest runs the ASCE 7 hazard tool against your specific project address, provides all engineered drawings and documentation, and advises on your jurisdiction’s requirements before you finalize your design. Installation is coordinated through manufacturer install networks for tubular buildings and referred professional installers for cold formed and red iron projects.
Serving Bennett and Surrounding Communities
We serve Bennett and its neighbors, including Strasburg, Byers, Watkins, Deer Trail, Aurora’s eastern edge, and the greater Denver metro. See the full Metal Buildings Denver CO page or browse all our Colorado metal building locations.
Talk to a Project Advisor About Your Bennett Project
Whether you know exactly what you want or you’re just starting to think through your options, a conversation with one of our Project Advisors is the most efficient path to the right answer. We’ll ask about your site, your use case, your local requirements, and your budget — and give you a straight recommendation.
- Call us: 417-218-8348
- Email: sales@amsteelmidwest.com
- Submit a project inquiry here
- Design your building online
Frequently Asked Questions — Metal Buildings Bennett CO
What is the best type of metal building for Bennett?
For garages, shops, and equipment buildings under Adams or Arapahoe County engineering requirements, cold formed steel frequently wins on total project cost. Smaller certified buildings keep tubular in play, and 60’+ clear spans or doors over 20′ are red iron work.
Do I need a permit for a metal building in Bennett?
Yes, in nearly all cases — the Town of Bennett in town, and Adams or Arapahoe County on unincorporated ground, all enforce codes with engineered drawings required on most structures. We confirm which jurisdiction your parcel falls under before you order.
What metal building sizes are most popular in Bennett?
Our most popular configurations are 30×40 and 30×50 for residential and small agricultural buyers, with larger agricultural and commercial operations frequently requesting 40×60 through 60×80. Browse our full inventory here.
Amsteel Midwest | 1014 E Broadway St, Bolivar, MO 65613 | 417-218-8348 | sales@amsteelmidwest.com
Metal Buildings in Colorado | Metal Buildings Denver CO | View Inventory | Contact Us